Adrian Router Login

ADAdrian

Need to configure your Adrian router? You can access the router settings by entering 192.168.0.1 in a browser. This guide covers the login process, default username and password, and how to update the Wi-Fi name and password.

This is not your router’s admin page.

To open the real router interface, enter 192.168.0.1 directly in your browser’s address bar while connected to the same Wi-Fi or Ethernet network.

Open 192.168.0.1 in a new tab

If the page does not open, make sure you are connected to the correct router and that the address is entered without extra spaces or search terms.

Quick Access

192.168.0.1

Alternative Addresses

192.168.1.1

192.168.100.1

192.168.1.254

No default credentials on record. Check the sticker on the back of your router or contact your ISP for the login details.

Note: The IP address, Username, and Password are printed on a sticker on the back of the router.

Log in to your Adrian router

1
Make sure your device (computer, phone, or tablet) is connected to the router — either via Wi-Fi or with an Ethernet cable plugged directly into the router.
2
Open any web browser and type http://192.168.0.1 into the address bar. Press Enter. If the page does not load, try 192.168.1.1 or 192.168.100.1 instead.
3
Wait for the login page to appear. This may take a few seconds.
4
Enter the login credentials. If you have never changed them, check the sticker on the back of the router or the documentation from your Internet provider.
5
After logging in, you will see the router dashboard where you can manage all settings.

Change the Wi-Fi name on a Adrian router

1
Log in to the router admin panel as described above.
2
Open the Wi-Fi or wireless settings. Depending on the model, the menu may be called "WLAN", "Wireless", or "Wi-Fi".
Example path (may vary by model): Wi-Fi Configuration > Wi-Fi 2.
3
Find the field for the network name (often labeled SSID or Network Name) and enter the new name.
4
Click Save or Apply to confirm the changes.
5
Your devices will need to reconnect using the new network name.

Change the Wi-Fi password on a Adrian router

1
Log in to the router admin panel.
2
Open the Wi-Fi security settings. Look for a section called "Security", "Wireless Security", or "WLAN" in the menu.
Example path (may vary by model): Wi-Fi Configuration > Wi-Fi 2.
3
Enter a new Wi-Fi password in the password or passphrase field. Choose a strong password with at least 12 characters, mixing letters, numbers, and symbols.
4
Click Save or Apply to confirm the changes.
5
All connected devices will need to reconnect using the new password.

ⓘModel and firmware differences

The exact menu names and layout may vary depending on your Adrian router model and firmware version. Labels such as "WLAN", "Wireless", "Network", "Security", or "Wi-Fi" may look different on your device.

If the login page does not open

Common router troubleshooting steps: disable VPN, try a different browser, clear cache, use Ethernet

Having trouble accessing your Adrian router settings? Connection issues, rejected credentials, and slow-loading admin pages are common problems. Below are the most frequent issues and how to fix them quickly.

⚠192.168.0.1 is not reachable

Make sure your device is connected directly to the router, preferably via Ethernet cable. Double-check the address for typos. Try restarting the router and wait about 30 seconds before trying again.

⚠Login credentials are not accepted

The default credentials may have been changed by you or your ISP. Check the sticker on the back of the router for the current password. If it was changed and you cannot remember it, a factory reset will restore the defaults.

⚠The page loads very slowly or times out

Disable any VPN or proxy settings on your device. Try a different browser or use incognito/private mode. Clear the browser cache. If you are connected via Wi-Fi, try using an Ethernet cable instead.

⚠Wrong IP address?

Some devices use a different default address. Try these alternatives: 192.168.1.1, 192.168.100.1, 192.168.1.254. You can also find the correct gateway address in the network settings of your operating system.

⚠How to reset the router to factory settings

Locate the small reset button on the back of the router (you may need a paperclip). Press and hold it for at least 10 seconds until the LEDs start blinking. The router will restart with the factory defaults, including the original login credentials.

Example screens

Interface screenshots for this device will be added soon.

Frequently asked questions

Which address should I use to log in to a Adrian router?

The default login address is 192.168.0.1. Enter it in the address bar of your browser to open the login page. If that does not work, try 192.168.1.1 or 192.168.100.1.

What can I do if 192.168.0.1 does not open?

Confirm that your device is connected directly to the router. Check the address for typos. Restart the router and wait about 30 seconds. Disable any VPN or proxy connections. If the problem persists, look up the correct gateway address in the network settings of your device.

How do I change the Wi-Fi password on a Adrian router?

Log in to the router admin panel, navigate to the Wi-Fi security settings, and enter a new password. Click Save or Apply. All connected devices will need to reconnect with the new password.

My ISP changed the default credentials — what now?

Many Internet service providers set custom login credentials during installation. Check the documentation your ISP provided, or contact their support. A factory reset will restore manufacturer defaults but may also reset Internet connection settings.

How do I change the Wi-Fi name (SSID)?

In the router admin panel, open the Wi-Fi settings and find the field for the network name (SSID). Enter the new name and save the changes. Your devices will find the network under the new name.

You might also find helpful

192.168.1.1 192.168.0.1 10.0.0.1 192.168.1.254 fritz.box routerlogin.net Find Router IP Address Change Wi-Fi Password